Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Software : C / GCC - SDK 15.0.0 - SD140 6.0.0 - building on multiple platforms. Hardware : nRF52840-DK (Q1AAC0) - and secondary testing on custom board using the Fanstel BT840...
I have been at this for a few days now, I have had a number of compilation errors that I have had to work through and find solutions for, but I am stumped on this current...
I'm trying to use the low-power comparator.
I've started up the comparator using "lpcomp_init()".
Following that, I wish to have a sample event, and then log the result...
I am trying the example here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_att_mtu.html
I want to lower the sleep...
Hi,
How do I enable Band 1 on my Thingy 91? On your web-page it seems that your base-band supports Band 1, but when I use the following AT-command AT%XCBAND=? I get the...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
Hello, I am making my first custom board based on nRF52832. I have used a custom antena design (due to PCB layout I did not use reference design). That was the very first...
Hi everyone,
We need your help with a condition that we encountered in our prototype of a nRF52840 that use a ceramic antenna. Our current design is poor and we will have...
Hello,
We have the following problem with a custom board based on the nRF52832 and the SKY66112-11 PA LNA, running as a mesh node.
The SDKs used are nrf5_SDK_for_Mesh_v3...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
My queries are:
1) In code I just changed...
Hello,
I have queries on Sniffer functionality.
1) Using nRF52840 USB dongle whether we can sniff BLE 5.0 packets.
2) Using nRF52840 development kit whether can I...
