Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
It's NRF52832 and NRF52810.
The BLE connection process is to establish a physical connection first and then discover the service to obtain the characteristic word information...
Hi,
For my application, I would like to have multiple watchdog timers. I am measuring several sensors (I want one short-term watchdog timer to be fed in this loop, pause...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
I am using SDK 15.0 with the Nordic NRF52840 development board. I wrote my own custom bootloader using CDC ACM as the transport. I am using app_usbd_cdc_acm_read_any to read...
Hello All,
Is there any already available example of OLED display interfacing with nRF52DK, pca10040, SDK 14.1 in Segger Embedded studio?
I am working on a project...
Hi，
I want to measure the time of two signals to calculate the speed and sent the data with BLE. I find the SD effect the GPIOTE_interrupt sometimes, when I try to use GPIOTE...
I an trying to locate and download some programming examples. For instance the BLE Blinky application
ble_app_blinky_c says it is in the EXAMPLE FOLDER, no matter where...
Our project uses nRF52832, and the bluetooth connection has two modes as follows:
one is low-power standby mode connection interval=1000ms;
One is data transmission mode...
We have recently ported our application from SDK 12.2 to SDK 14.2. The application is very power sensitive and uses a high connection interval and slave latency to minimise...
We have a project running based on the SDK 14.1 on a nRF52DK with S132 5.0. The used bootloader works as expected and also an update of the bootloader works properly.
After...
Developing medical sensors for medical institutions according to legislation ( us-fcc.app.box.com/.../8acz9o1cah6eqqpm2q3ktvfkkqt37v7p) in the 2340-2400 MHz band - nrf52 seems...
Dear Sir,
I want to access two slaves viz. MAX30205 & LIS3DH by using nrf52832. The problem is, as per the datasheet the values of the pull up resistors required by both...
Cannot get nRF Sniffer version 2 (beta) to work properly with nRF52 DK running the sniffer_pca10040_51296aa.hex:
Windows 7 64-bit
nRF Sniffer 2.0.0-1.beta
Wireshark...
