Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hi,
this is how I initialize and enable LPCOMP
nrf_drv_lpcomp_config_t lpcompconfig = {
{NRF_LPCOMP_REF_SUPPLY_SEVEN_EIGHT, NRF_LPCOMP_DETECT_CROSS},
APP_IRQ_PRIORITY_LOW...
Hi,
I wonder if BLE_ERROR_NO_TX_BUFFERS(s110) and BLE_ERROR_NO_TX_PACKETS(s130) have same meaning.
These marco variables are defined in ble_err.h.
Thank you.
HI,ALL,
i am so sorry for my silly question here.
In ble CORE SPEC,
i saw a sentense (Version 4.2 [Vol 1, Part A])below:
"Device L is shown in the same locality...
Hi,
The SDK6.1 bootloader seems to have problems when used on a Laird BL600 module.
I'm using a BL600 with the SDK6.1 and SD7.1. I want to implement the bootloader in...
Hello!
As per documentation, RSSI is measured during the time, when particular packet is being received. In particular, nRF51822 Product Specification v3.1 states RSSIperiod...
Hi, i have a NRF51-DK (nRF51822 - PCA10028) board and using SDKv10 with SoftDevice S110.
I read everything i could find about this topic and i see people claiming data rate...
I am looking to synchronize collecting of data from outside devices with the connection interval of the nRF51822 and the S110 vers. 8.0 softdevice. Are there specific events...
I want to send big amount of data (10kb) with characteristic of 16 bytes. when the phone side is subscribed to notification I run a loop of data sending.
how can I synchronize...
I have read through the forum on this and I am still not completely clear. Here are my questions:
Can I create characteristics that are larger than 20 bytes? The Bluetooth...
In looking at the nRF51 UART Example I'm wondering about data loss over the Bluetooth interface.
When bytes are sent to the host, is there a re-transmission mechanism somewhere...
Hello,
I was just editing the handling of sent packets and I wanted to evaluate the contents of the ble_gattc_evt_write_rsp_t struct which is part of the BLE_GATTC_EVT_WRITE_RSP...
Hello,
im using NRF 51822 with SDK 10 / S110 8.0. Im working on a project that includes one or two timers (initialized by APP_timer function), the ble calender (like discriebed...
Hi,
Because I didn't want to keep with the last question when this is a tottaly new one, so created another question.
I've tried to get this project to work:
github.com...
We have a communication problem between nRF24LU1+ and nRF24L01+ chipsets. nRF24L01+ uses STM32F4xx MCU on board.
Is there an RF sniffer that sniff the protocol?
