Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
ble_app_uart_s110_pca10028_nuevo.uvprojx
Hi, I´m using a nRF51244 with s110. I program it in nRFgo Studio (s110_nrf51_8.0.0_softdevice.hex)
I try turn on the passkey...
Hi,
I performed an OTA update of my APP. (SD 7.0 and BLE single bank bootloader were flashed).
The update finished without an error and then my application even starts,...
Hi,
I'm developing on a custom nrf51822-based board, and using the s110 softdevice, version 7.0.0. With JLinkGDBServer and the toolchain's gdb, I can debug softdevice-less...
Do you have a BLE SOC chip that can behave as a master and a slave, and also has embedded stack so no host processor is needed. I am looking for a chip that can be used in...
hi,
Inorder to flash the softdevice to evaluation board PCA10024 , i tried using nrfgo studio as mentioned in the user guide.but the nrfgo studio does not show any board...
Dear all,
I am using SDK7.1 with S130 v0.5 alpha. Can I use the DFU example in the SDK6.1 to update my firmware in the chip(nRF51422)? If not, is there any alternative...
I am using S110-based peripheral device which is sending 20byte notifications. Application on my peripheral works fine (testing with MCP gives transfer rate about 15kB/s which...
Hi,
I was using nRF51DK with Keil uVision ver 5.14 and SDK 8.0.0. It worked okay yesterday and I tried HW peripheral as well as BLE peripheral.
But today it doesn't...
Is it possible to identify a device as a previously bonded peer based on the advertisement package and before establishing a connection?
I would like to be able to bond...
Hi
Im using nrf51822 board from RedbearLab. SDK6.1and SD7.1.0.
I added DFU to my application and iam able to update the firmware OTA.
My issue is after adding dfu...
Hey there,
I am looking for the right pin out to wire up a reset button to my board so that I can reset the IOS device is paired to. Can some one help?
Tyler
Hi,
Is it possible to set an address lets say for an array to be in Flash memory on compilation?
So that way I dont need to reserve memory twice - once in my program memory...
I have two nrf51822 devices with sniffer firmware. At the beginning all tests were well, it can sniffs beacon packets with ble-sniffer_win_1.0.1_1111_Sniffer and display packets...
[edit]
This problem is solved!
The problem is from project target.
I am using uvision5, but I opened the uvision4 project. (\arm4...)
Now I am using the example under...
I am using the Sys Events to monitor the POFWARN but it appear that I get a POFWARN event repeatedly when the voltage is below the threshold is this normal or do I need to...
