Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I have two devices and one host. When they are in close area both of them are pairing to one host. When I switch off host, both devices looks like paired to each other...
Having gotten through the hurdles of getting my IAR project to compile and run on Segger Embedded Studio, I am now seeing different behavior between the two IDEs while debugging...
Hello,
In my application (based on app_nus_uart example, with two NRF52832 boards), one of the cases is uploading/downloading files with sizes up to 10MBytes.
In my app...
Can someone explain the reasons/benefits of using the single vs dual bank BLE boot loader?
Actually, why isn't there a single bank BLE bootloader in the example project...
I have following code which should start the app_timer and blink the LED_1.
When flashed, the LED_0 turns on and I can see the "Started." log. But the LED_1 is not blinking...
Hello,
I use nrfutil to generate the dfu .zip file, the error log is listed below. what is the reason? the softdevice is s140. thanks.
>>nrfutil pkg generate --hw-version...
ble_app_uart_c_pca10056_s140 fails with an assertion - I have downloaded nRF5_SDK_14.2.0_17b948a. For the example project examples\ble_central\ble_app_uart_c\pca10056\s140...
Hi,
I am trying to write a 120 byte data through ble to raspberrypi from my android app(I increased the MTU to the required limit). But all I am able to transfer is first...
Hi Team
Let's assume, we have a provisioner (client) and several successfully provisioned servers in a mesh network. We now want to remove one of these servers from that...
Hello,
I am currently migrating from SDK12.2 with softdevice S132 V3 to SDK14 with softdevice S132 V5 and have a problem configuring device names larger than BLE_GAP_DEVNAME_DEFAULT_LEN...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
I have found that new sections have been added in the linker file of the examples like sdh_soc_observers...
Hi,
I use SDK v13.0.0 with SD S132 and to debug my application I use UART0 on Putty.
When I use SPIS (0) (no BLE and no softdevice) alone I perform all functionalities...
hello：
i use timer1 to get a pwm waveform，when i use RTT to test it，the waveform is ok，but when i take out the RTT，and Remove the battery and put on the battery again to...
