Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hello,
When I try to read data from UART RX port using serial library, I'm not able to read the data beyond the number specified by
SERIAL_FIFO_TX_SIZE and SERIAL_FIFO_TX_SIZE...
Hey, I'm using raspberry pi 3 model b, with the rasbian strech os running in it. I have followed the tutorial provided by nordic using this link for BLE over IPv6. When I...
Hello, In my case, i'm using some PTX and one PRX. It's working well. Now i want to extend coverage, can i use repeater/forwarder? I tried but have problem with PTX: after...
Hi,
we are using a custom board, with codes tested on a NRF52 DK. We reconfigured the pins and when using pin P0.09 (by default NFC) as an input "active_high" and with ...
Hello,
I've done this steps:
I erased the whole chip: nRFgo Studio/ DeviceManager/nRF5x Programming/Erase all
I programmed the Softdevice s132_nrf52_5.0.0_softdevice...
Hello Nordic Team,
i use SDK 12.3 and SoftDevice S130.
In the template project ( \examples\ble_peripheral\ble_app_template ), the BSP module is used to indicate advertising...
Hello,
For my project I need to send raw data (without prefix or timestamps ) along with system logs trough the same UART.
So far one possible solution is to use NRF_LOG_RAW_INFO...
I've been using nRF24LE1 for development. The HAL library provide the AES encryption for ECB mode. Now I need the decryption function. Does anyone has the realization? Any...
Hello everyone,
I use SDK14.2 and s132 softdevice. I can read "NRF_SAADC_INPUT_AIN0" and "NRF_SAADC_INPUT_VDD" pins and system is working properly.
Working Code like...
Dear friends,
I am using the nRF 52832, s132. I want to know the BER (bit error rate) of the BLE link. How can i measure it? Further, to what extent do other radio interferences...
Hi.
I want to know the time difference between functions by using a timer instead of a difference. I've looked at app_timer.h, but it's hard to understand.
I do not need...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
