Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi I'm doing a school project where I'm going to make a bluetooth mesh network where I use nrf52840. where i tried to get "light_switch demo" to run, but i have some trouble...
Hello,
Could it be possible to do an update with a zip DFU file stored in a flash memory ?
What is the best way to do the modifications (mainlines) ?
Thank you
Hi,
I'm using two nRF52832 (SDK14.2, SD132v5) to send data via Notify to one central. This central can be either a laptop or a smartphone.
The two nRF52832 has the same...
Hi all,
I am using nRF52832 SoC and nRF5 SDK for Mesh v1.0.1. I know until now there is only support for relay feature in the Mesh SDK. I want to implement low power feature...
Hello,
I was trying to connect my boards to nRF Cloud to evaluate it. Setting up Gateway on the phone and on the web at nrfcloud.com was rather easy (just following getting...
I use the SDK9.0，When a bluetooth device and android APP to connect, disconnect the bluetooth device power, why wait for 20 seconds, the APP to detect device has been disconnected...
Hello Everyone,
I want to know that i purchased NRF51 DK ..which includes PCA10040 IC.i'm using MDK ARM KEIL5 . now if i'm going to develop one BLE product so i don't know...
Good morning.
I have two nrf-51 boards and a mobile device, the SDK that I´m using is the v.12.2.0. I need that the three devices are connected at the same time and its...
Hi all,
My configuration:
nrf52832
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using th e secure bootloader example located at \examples\dfu\bootloader_secure_ble...
The nrfgprgret register is used from the application(custom) to trigger the system into dfu mode. The nrf 52 enters dfu mode and a zip file containing bootloder.bin/.dat and...
hello, I check the standard example nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs device nrf52DK PCA10040 V1.1.1 ARM Compiler :...
I am currently considering purchasing the UBLOX NINA-B1 module. This uses the Nordic nRF52832.
The very 1st thing I wish to do is to be able to send and receive information...
Hi Nordic,
I have managed to make a board which has both the nRF52 and PN532 modules on the same board (picture) , connecting it through I2C as shown on the example here...
The Event Generator Unit peripheral is new in nrf52. There is a basic description in the current manual of nrf52, but not much can be inferred as to how to use it. Could an...
