It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Nevermind: my problem seems to have been: you need a battery at 3V powering a BLE Nano to program it from a nrf52DK.
Original question: I have connected a nrf52DK dev kit...
Hi all,
I am new to write firmware of ble device(Bluz). I wanted to change the default firmware of ble device. For that, I wish to write own firmware. Please guide me,...
Hi
I'm trying to catch the GPIOTE_IRQn interrupt, while the device is in system off.
Not enabling the SD130 V2 the interrrupt is caught once, and then not anymore...
...
Hello,
I'm currently trying to pair my board with my phone and I've faced some issues.
After downloading my device(NRF52 PAC10040 board) with experimental_ble_app_blinky...
Hi all Nordic developers,
I am currently working on nrf51 to scan all the nearby beacon and then i wish to send the data to the esp8266. I already able to scan all the...
When I try to copy a zip file from my email to NRFToolbox for DFU, the NRFToolbox app comes up and then immediately crashes.
Steps to reproduce:
Download latest NRFToolbox...
Hello, as it is clearly understood (by everyone developing using NordSemi's SOCs), this struct "ble_evt_t"
Hello, as it is clearly understood (by everyone developing using...
Hi,
I've read in your press release for SDK 12 that increasing the MTU beyond 23 bytes is now possible on the nRF52. I thought I'd test this increase out on my nRF52 with...
Hi All,
I have a basic question, i want to know what are the right value to use with the nrf51422 chip for the resistors with ADC.
I want to use the maximum value permitted...
Hi, I have problem with using example codes. I want to add GPIO control to ble_app_uart example. Adding gpio_config() function taken from app_timer_tutorial blocks program...
I'm using NRF52832 SoC and IAR
I've to read data from ADC using SPI. ADC will generate interrupt every 4ms indicating data ready. I've configured GPIOTE to sense the ADC...
A couple of power consumptions Q's for this basic scenario: RTC used via PPI to infrequently sample from ADC and trigger SPI read from external sensor source.
Questions...
Hello,
I need a support for BMD-300 BLE module.
We can flash the BLE module and we can connect it with mobile application via Blue-Tooth.
But when we flash BLE for...
