Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\nrf52-ble-tutorial-service.uvprojx and compike then find...
hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\ nrf52-ble-tutorial-service.uvprojx, and compile ,the result...
Hello,
I am developing custom driver for TWIM. I am facing a problem with DNACK and ANACK which hangs my application. SCL and SDA lines are monitored through Saleale logic...
hello,
again, sorry for the begginers qustion(probablly i will have 2-3(hopefully) in the next few days). I got today the nrf52-dk, and on the back of the nrf52 is written...
I ask the questition yesterday ,maybe i have not expressed clearly.In my project , I have to use three spi in master mode and three twi in master mode to communicate with...
Hi!
In my teamwork we are developing an application for use a sensor module via spi, and share data and comunicate with other devices via Bluetooth.
I've taken care...
Dears,
We are working for a dongle solution to exchange data.
Have any BLE SDK solution via Uart to exchange data between host & client? and that the host is no need...
Hi,
I am using nRF51822xxaa and s130 and SDK 10.0. nRF51 connects with the app(notifications enabled), then bonds with it. Subsequent communications between the app and the...
I connected with RTT Viewer 5.12f with nrf51 DK board.
while I donwload firmware to the board, I got bunch of error message from RTT viewer..and it stop..sometime the download...
I am having two issues with the following code:
When I run this sample code on my NRF52DK (there's external hardware connceted but that does not affect this operation...
Hello, everyone~
I used to see nRF51802 in an official document but cannot find it in the official website. Is there an nRF51802? If so, what are the differences between...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
