I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
My ble device try to notify a data to my android mobilephone after phone connect it,but sometimes,phone can't receive the data and error 8 occur .this happend frequently when...
Hi,
pstorage_raw_store() API fails as p_src address is not 4 byte aligned (i.e. 0x20002b1a), as p_src is RAM address and also as its "SOURCE" address is it necessary to...
Hey Folks
I wonder to design my own simple circuit based on NRF51422, the circuit should connect to a mobile app. By the way I'm I wonder to follow these steps:
visulaised...
Hi all,
I have one question about the deep sleep wakeup process in NRF24LE1. I want to realize the function that "when I press the button, it will cause rise edge on the...
Hi,
I'm testing doing a soft device update (v7.0 to v7.1) over DFU, but I consistently get OP_CODE_SYS_RESET sent to my device after 4 packets(80 bytes), at which point the...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
I'm currently designing a system that requires Nonvolatile memory. Whilst I can accept the 43uS delay to write a word to flash memory. My concern is that it is entirely possible...
