hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I was trying to view the scan response packet using the master control panel app I have on my android phone, but I can't seem to see where it is.
I want to update the scan...
I'm looking at an application where it would be beneficial to be able to read data from the bluetooth device as it passes. It would be easiest for me to do this by simply...
I am using the TWI module in master mode, with sdk 10. I purposely create an error situation, in which the TWI gets stuck and keeps returning NRF_ERROR_BUSY every time I try...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
Hello,
i would like to scan for a custom UUID Ventor. And when the BLE Central found this BLE Client.
I will Change one Output pin from low to high.
I start with the...
hi,
after connecting to peripheral device. app_timer_cnt_get() function always gives 0. why it is so. i am not able to understand it.
can anyone help me to get the current...
Hi all,
Can I do something like this:
The SPI master sets CSN line low.
The SPI master sends multiple packets. And the total number of bytes exceeds the...
I want to transfer data collected in my nrf52DK to nRF51 dongle at regular intervals. Right now I can use master control panel in PC to receive the data. Is there any way...
I am using the bootloader from github here to upload DFU over-the-air using an android phone. It works fine for bootloader and application uploads. But if I upload the softdevice...
I'm looking for a radio module for a harsh environment (steelworks furnace)
The module has to work at high temperature 80°C and must transmit 16bytes every second at a distance...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
