Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
I don't understand why i have a current consumption of 0.535mA in system off.
In my soft i use PWM, SPI a Button,, I put all things off before i go to system off but still...
hi all:
I download the nRF OpenMesh from the GitHub.
There are 4 example in this folder:
(1)Bandwidth_test
(2)BLE_Gateway
(3)ping_pong
(4)Template project
I prepare...
Hi,
Starting from the LED Button Service found in SDK_12.2.0/examples/ble_peripheral/experimental_ble_app_blinky I'd like to add two characteristics on this service. I...
Hello!
Based on you example I try to develop a simple HelloWorld example that follows chapter 11 of the specification. It says that to form a network a energy scan should...
Hello,
I have been investing a couple days now in order to get the DFU procedure working properly, but it seems I am stuck...
This the setup that I am currently using...
Hello,
I seem to be having some errors with my current project. I am using SoftDevice S310 Version 3.0 and SDK 9.0. When i try to communicate with one of my I2C sensors...
Hello,
When using hal_w2_read() and hal_w2_write(), should the 7 bit address of the slave be passed in or the 8 bit read/write address?
It seems to me that passing in...
I downloaded the nrf52 SAADC Low power project from the GitHub
github.com/.../saadc_low_power
I'm trying to migrate it over to version 12 of the SDK and I think I'm having...
Hi. I'm using nRF52832, SDK13, S132V4.0.2.
I'm trying to test DFU.
I have 2 questions.
Q1. How can I make image for merged files?
I can see it works very well when I...
I am in the process of porting an nRF51822 (s130) project to the nRF52840 (s140), moving from the SDK V11 to V13.
I was using the BLE_EVT_TX_COMPLETE event in the SDK V11...
I've seen in two different posts that some people were trying to use this Torex XC9265A181MR-G in terms of being able to use a 3.7V LiPo battery. Can someone tell me if he...
I just bought the NRF51DK and going through this getting started guide: devzone.nordicsemi.com/.../
I opened the file ble_app_uart_pca10028_s130.uvprojx in folder ..\examples...
Guys
I am a newbie using nordic modulesI am just starting to program here with a nRF52 and SDK 12.2
I was trying to edit the experimental_ble_app_blinky and experimental_ble_app_blink_central...
