Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
As title, im using nRF51822 as a ble uart.(ble_app_uart)
But it will sleep when No connect for some time.
how can i turn off the sleep mode?
I want it be a "always...
Hi, may I looked bad , but I can not find NTF52 documentation, datasheet, evaluation board schematic, pinout, price... nothing , except the file nrf52.h in which I found some...
The following SDK files have incorrect comments:
markrages@qountdown:~$ grep 'units of 0.625' -r /opt/nrf51sdk-11.0.0 | grep 300 | grep to\ 25\ ms
/opt/nrf51sdk-11.0.0...
I configured nrf to go to sleep after 5 minutes of inactivity and then wake up by external signal (by accelerometer interrupt if any movement detected). what struck me is...
Hi again,
I'm here with another HID problem. When I flash my chip with standard HID mouse example, OS discovers it with it's declared in code name, connects succesfully...
I have designed an custom application board based on nRF51822 SoC,
Now i wanted to do testing on RF front.
I found one Test guideline(RF_Performance_Test_Guidelines_v1_0...
Hello Everyone,
I am able to do this functionality by using NRF5DK
Using Android APP (MCP master control panel) am able to make beep sound in the NRF51DK by using...
Im working with a nRF51422 EK. So, there is an android application with 2 buttons. Each of them can Set a LED. It will be set as long as the button is pressed on the application...
SDK:10.0.0
Here is the error when I compile
..............\components\softdevice\common\softdevice_handler\softdevice_handler.h(40): error: #5: cannot open source input...
Hello,
I have a project which is currently using S110 SoftDevice v7.1.0 with nRF51 SDK v6.1.0. The hardware is nRF51822 xxAA revision 2. It will probably be upgraded eventually...
Hi,
I intend to use ANT protocol for an application of soccer players trackers.
Each soccer player would wear One master and remote sensors communicating with ANT.
But...
Is there a way to know if we are in critical region?
ie: between sd_nvic_critical_region_enter(&foo) and sd_nvic_critical_region_exit(0) without explicitly using a global...
Hello,
I'm using nRF8001 with Arduino for our project. I use BLEeripheral. h and I need to know if it's possible
with the visibility of NRF
when invisible can nrf...
Hi,
everyone,
I am new with the uvision IDE.
Can anyone tell me how should I supply source and header file to project so that my header files can be access without relative...
