Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hey All -
My team is new to Bluetooth development and so this may be a naïve question. Pardon us for this, if so.
We are trying to create an Android App that would scan...
Hi,
There is a difference of one digit in BT address and DEVICEADDR. Could anybody explain this? I know in the last byte we have to add C0, but what about the frst byte?...
I added CCCD descriptor to Battery Level characteristic in the proximity_setup.xml.
The nRFSTudio throws an error 0x01 while generating services.h.
Kindly help me generate...
8.0, multilink example, peripheral, s110 softdevice.
I modified the button_event_handler() function in main.c into this:
static void button_event_handler(bsp_event_t...
Hi....
I have a problem when i use dfu_dual_bank_ble_s130_pca10028 in sdk v11 on my board. cpu is nrf51822QFAA.it seems reset all the time. using keil debug, it's wrong on...
The CoAP block example has a "put" function, which works just as the instructions describe. It would be helpful if you could also show an example of the "get" function. These...
hello!
Is IoT softDevice for nRF51 DK has all the features of BLE 4.2??
I know IPSP is the feature of BLE 4.2, but i wondered whether privacy and data packet extension...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi All,
I'm using Nordic UART App to write 'A' to TX characterstic and then i expect some action after that as per my code on BLE nordic device, which is happening.
But...
I'm using the attached proximity_setup.xml ( proximity_setup.xml ).
I'm trying to use the Battery Service to send Battery Level notification.
I added the following code...
Hi,
I have just received a nRF52832 Preview DK and I am trying to set it up according to the description in the nRF52 Series - Get Started section.
I have connected the...
Hi All,
I am using nRF51422DK with SDK 10 and trying to communicate with an external peripheral over UART at every timer interrupt.
I have modified the ble_app_hrs example...
Hi All -
Is there anyone successfully able to autoconnect with nrf51822 with a phone/pc/tablet? I have been trying it for the past week and couldn't get my nRF51822 autoconnect...
I successfully turned off bluetooth radio using NRF_RADIO->TASKS_DISABLE = 1 when i do advertise_start(); after certain delay i coudnt connect back for data transfer
Based on nRF51822\Board\pca10001\ble\ble_app_hrs example,
How nRF51822 detect ADC input? Which ADC pin?
Configuration code:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit <<...