We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi All,
I am doing the certification (Japan Radio Law) now. I use the nRFgo software to enter the "Direct Test Mode" for test the each channel BUT I do not know how to...
I have designed nrf52832 customized board with tace antenna antenna and every pin of the controller is connected to the male headers present on both side of the boards. I...
I am using sdk 14.2.0 and I want to use nrf_calendar.h in my code but it is supported only in sdk 13.0.
will you guide me how can I use it in my sdk version 14.2.0.
the...
Hi,
Would someone please help me to configure a specif channel for continuous scanning. I was browsing through the forums and understand that the SDK/SD not supports these...
Hi together,
since quite some time I try to merge my BLE application with the SPIS functionalities from nRF52 SDK 12.3 example with softdevice S132. My application should...
Hi, I am developing a central device application using the ble_app_multirole_lesc example as a baseline. I am using v11 of the SDK. This example uses the heart rate service...
I am following the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img onto the RaspberryPi 3B+.
I have loaded the...
Scan of services after connecting to DFUTarg does not return
the new services on the device. Instead the old services that existed
on the device before going into DFU...
I'm trying to follow the guide Sending mesh packets in the Interactive PyACI section on the nordic infocenter.
I've installed the required prerequisites using pip.
Here...
SDK 14.2
This question pertains to the app_timer library.
Hi,
I am using the app_timer library for creating/starting timeouts.I had a question about the APP_TIMER_MIN_TIMEOUT_TICKS...
HI,
i n this modified example: https://github.com/Rallare/nrf51_ble_app_hids_kbd_consumercontrol/tree/SDK15 cI would like to define the long button instead of short button...
Hii,
We are using currently nRF SDK12 and nrfutil for performing DFU over ble. we are able to do it by pressing button on nrf51822 Dk kit at time of restart and putting...
Hi All:
I had a problem about programming.Does someone can help me? Thanks.
My IDE is IAR :ARM 8.22.2
Projcet: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Hi,
we are currently using nrf51822AC device and nrf SDK12 . we need to do "switching to bootloader without a system reset nrf51822" as mention in subject . actually we...
Hello, I want to send beacons from one nRF51822 device to another. My project involves using omnidirectional antennas. So, will nRF51822 be the right choice for me?
I was...
