when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
I tested the Heart Rate Monitor sketch code (Arduino Primo IDE code) and verified that it works with the Heart Rate Monitor through the "nRF Toolbox app" on my iPhone. I would...
There have been several topics on limitations on ADC sampling rate when BLE is in connection.
However, I didn't see notes applicable to the following case:
nRF52832, sampling...
Hello all,
I have some troubles to initialize the micro SD card with my custom board.
I have used the nRF 52 DK to write a basic code and do some test. For micro card...
I am using nrf52832 DK and am unable to build my light switch example. It throws an error that some files are not included. In the screenshot, you could see the error. I have...
Hey Everyone
I have written a code for using lora rn2483 with nrf52840 using the uart protocol which is configured on 7 and 5 pin. The program was working fine untill i...
Hi,
I am using the nRF52840 DK and the wireless_uart example from nRF5_SDK_15.0.0 to try and receive data from other 802.15.4 sensors. Using the example I can receive messages...
Hello everyone!
I'm very shy to ask probably a stupid question, but...
I'm trying get abitity to change pwm signal via ble.
I've created service, characteristic, then I...
Hello,
I am trying to get a low consumption and I detect that the activation of the ADC increases the consumption. So I am trying to configure the ADC and when I make...
NRF52832 / S332 / SDK 14.2
Step 1: connect to mobile phone as Peripheral Role, and the connect handler of service was #0 that equal to Peripheral-connection handler number...
Hello,
We are using nRF5 SDK14.2.0 and soft device s132, and trying to perform DFU of the Bootloader itself.
The process fail in nrf_dfu_postvalidate() due to wrong HASH...
i am trying to Connect a custom board with the nrf52 over the bluetooth. nrf52 is running with the BLE_nus
.i am trying to connect it with the uuid in the program is like...
Hi. I`m trying to connect two Nortdic Thingy device and receive data in same time(ex. temperature, humidity etc..).
In my application, I can connect two devices in same...
I have most of the SDK up and running with my firmware, but I cannot find where to limit the number of bonded devices to my module.
I could live with just deleting all the...
Hello,
Is there a way to get the output log for the Mesh Light Switch Demo to output over UART instead of RTT? We are using a Fanstel BT832X module containing an nRF52832...
Hello,
I am currently trying to implement SAADC sampling from three channels into the same sample buffer (device is a 3-axis accelerometer, ADXL335). The root objective...
