I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am trying to disable rx after starting data transmission, is there any way to do this for ble projects, and is there any advantages in terms of lower power consumption?
txidle.png
In the attachment there is a method to reduce delay while transmissiom. Do you think this can help lower the power consumption? If so how can we do this using...
Hi,
In pstorage.c, function uint32_t pstorage_init(void), there a call to sd_flash_page_erase (line 846):
// Erase swap region in case it is dirty.
retval = sd_flash_page_erase...
Hello,
I'm curious about how to deploy my application to multiple nRF51 Dongles at the same time while I am developing. I have the same application / hex file running on...
Hi,
I'm trying to connect my nRF51822 PCA100001 development board to a ARM M3 processor via the SPI. In this case the ARM M3 is the SPI master and the nRF51822 is the SPI...
Hi,
I am having a nRF51 DK(PCA10028) development kit. I am trying to run blinky example on this development kit using Eclipse+GCC environment. I am following nAN-29 application...
Hi, I'm trying to locate the Softdevice whitepaper (nWP-20), the S210 softdevice specification makes reference to it, but I can't seem to locate it anywhere on the nordic...
Hello Everyone ,
I want to use pstorage for my project.i get the example code from here
devzone.nordicsemi.com/.../
and its working properly(i.e read and write operation...
I am using nrf51822, after establishing connection between master and slave, circuit needs only tx antenna, is there any way to put rx in sleep mode for ble application? During...
I have some nRF51822 MBED kits and I want to use them for BLE for both peripheral and central roles. I understand that this is possible with the S130 SD and the Nordic SDK...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
It took a bit to learn these offsets and configure the keil project for them. Do these need to change now that I want to begin using the OTA bootloader? I'm imagining that...
It's probably a rare bug, but it is still worth noting. I have been debugging this issue for a day.
I am using SDK 6.1 at the moment.
The problem was that Device manager...
Hello everyone, right now i make my own nrf51822 kit. it works good for all sample example when i use minimum current consumption example it shows 4.5uA current, then i erase...
