Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I'm using this code to log the BLE MAC address on my peripheral device, an nRF51822.
void ble_log_mac_address(void)
{
// Log our BLE address (6 bytes).
ble_gap_addr_t...
Hi,
I'm basing my project on ble_hrs_freertos example project (nRF52832, SDK14.2, PCA10040)
When calling assert(condition) in the original example project, it works...
Hi!
We are evaluating the 52832 soc for use with a DALI-controller. The communication speed with the controller is at 1200 baud, Manchester encoded. Is it possible to interface...
In BLE communication, I want to send 244 bytes of data from the peripheral to the central every 50 ms, is it possible? If possible, please tell me the setting method.
Hello, I have a problem with the configuration of GPIOTE low accuracy pin interrupts. My code is running on nRF52832 and already uses ble stack, PWM1 and PWM2 instances with...
Hi,
Right now I have a program on nRF52-DK (SDK 11) that scans for BLE adv packets, and transfers data from some specific addresses to PC through UART. Around every 10ms...
I'm attempting to use the PPK with the nRF52840 PDK with no success. I'm getting nothing running the nRF Connect with the Power Profiler. Configuration is as follows:
nRF52840...
Hey Guys,
Have been playing around with various MTU sizes to better understand throughput. I'm curious about one scenario though. Let's say for example that we are using...
Hi
We are using a slightly modified (but fully compatible signed bootloader) in out product. On the application side we have a C# implementation of the DFU protocol that...
Hello there,
In my next project I need a data link similar to BLE classic (like the HC-05 module) and it needs to respond with an app API fast and push data rather then...
Hi,
I'm following "ble_app_uart_c" example and works very well with SDK 10.0.0. So now I want to communicate with HM-10 module, but this has one Tx/Rx Characteristic. Are...
Hello,
In my quest to monitor the activity of hundreds of nodes (directly addressable), I am facing quite an obstacle.
The small memory of the nrf52 (nice piece of hardware...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
