I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
When I try to generate a log file by clicking Log File... in master control panel. The following error message comes up.
error_log_file.png
I would like to create a...
Hello dear Nordic community,
currently I am working on the NRF51822 Direct test mode (DTM). I tested the ble_app_dtm example and it works fine for me.
This means I can...
Hi,
I bought nRF51822 Evaluation Kit and would like to blue wire an external MCU( Kinetis Cortex-M) to talk to the SoC. It looks like the SoC on this board has many GPIOs...
Hi,
Could someone can explain, how to handle Static Passkey in iOS Central application?
I would like to know whether iOS application allows static key based pairing or not...
Hello,
i'm programming an iOS app to connect to the nRF51822 (peripheral). The Problem: Any kind of authentication and encryption is needed, but in the final Product the...
I've seeing random crashes at that originate from ll_lm.s0.c:404. It seems to be happening when I have uart logging turned off. I don't think i've seen assert callback called...
Says it all in the title. I'm making a sensor which puts its data in a non-directed non-connectable advertisment packet. I want to read the sensor just before it is sent....
Hi,
We are designing our 2nd pass design based on nRF51822 this would be our production version PCB.
We would like to have our Schematics,Layout and BoM reviewed from your...
Hi,
I am using softdevice-7 and SDK 6.1 for our application. I want to implement static key pairing for serial port over ble application "ble_app_uart".
I have implemented...
I have a 384 byte, writable, variable length, vloc user characteristic and I want to trigger an event when the write completes so my application can operate on the data. ...
Hello-
I am trying to program a custom nRF51822 board with a J-Link-lite.
From the J-Link-lite, I am using the 10-pin header and have it wired like this:
I'm using pins...
I have a situation where I need a software PWM for several channels, which are multiplexed via a shift register.
The output loop needs to run at several kHz for this to...
Because of the limitation in the GPIOTE hardware that only one channel can be connected per GPIO , care must be taken when changing a PWM duty cycle. If for instance the compare...
Links: https://devzone.nordicsemi.com/documentation/nrf51/6.1.0/s110/html/a00081.html#ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works...
