Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I am trying to run nRFToolbox App, I imported the project to Android Studio but I get the following error when I attempt to run it:
Error:Execution failed for task...
I just switched over from SDK v6 to SDK v7.1 (installed via those Keil Packs). The UART has suddenly stopped working (via Segger USB COM port) and I can no longer see any...
Hi Nordic,
I used PIC32 for SPI Master and nRF51822 SPIS slave. I used shortcut for my spis in nRF51822 and I need to know the right time of acquiring the semaphore and...
I have a 32 byte string to read and write using SD110. In the MCP I can read (using read long) the whole string without any problems. When I try to use write long, MCP times...
I'm getting started with the ble_app_hrs_s110_pca10028 (nRF51 PCA10028) example in the nRF51_SDK_7.1.0_372d17a_packs.zip SDK. See the tags for my hardware setup. I'm using...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello ,I want to scan the Bluetooth peripherals through one master application and want to display the Bluetooth peripheral names on serial window like what master control...
I am new to nrf51822.
I am trying to convert my Arduino code into NRF51822
I need something like this
currentMillis = micros(); //microseconds since the Arduino board...
Hi,
Without dissecting the provided Raspberry Pi Debian packages -- is there a list of the required Linux kernel modules and binaries required for the IoT Dev Kit example...
Hi there. I'm currently trying to run the BLE_APP_HRS example from IAR workbench on nRF51822-Evaluation-Kit.
We are very interested in using this chip in our upcomming products...
Hi All,
I noticed CSR has just released something called CSR mesh, please see: http://www.csr.com/news/pr/2014/csr-mesh , and a demo video: http://www.youtube.com/watch...
I'm renewing my search for a point-to-multipoint radio system, preferably based on the nRF51822. Basically, I need to be able to connect up to 32 (or more!) nodes to a master...
I am trying to implement a mesh protocol using the nRF24L01+ transceiver.
After reading the product specification, I have concluded that the Enhanced ShockBurst cannot...
I'm working on a wireless sensor network and was thinking about using nRF51822 as the primary SoC. For my network it would primarily be low power sensors talking to one another...
