Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
hello there i want to use low power comparator nrf51. now my device work with battery. so i think i require internal reference. now can you tell me how to use internal reference...
Hello, recently I've found an information about bit counter in Radio Module in nRF52 Product Specification. Unfortunatelly I can't find any reference at infocenter how to...
Is MTU of all BLE devices limitted to 23 bytes when using ATT protocol?
I don't know explicitly.
Some say it is possible to use MTU longer than 23 bytes.
Others say...
I am using TAIYO-YUDEN EYSHCN, which is having Nordic-nRF52832 chip on it. As per document from TAIYO-YUDEN, recommended to flash s132-firmware on it. I downloaded s132_nrf52_3...
I have two questions with the remaining unresolved symbols being the most critical. I will decribed the situation I have encountered as a sequrence of chronological steps...
Hello,
I have a need to construct multiple portable devices on a short time frame. We expect that building Arduino-format shields for our peripherals and using nRF52 DK...
I am using PWM on a BLE Nano using Nordic SDK. I was having problems with the PWM and decided I would set the duty cycle to 0 to see if the program was working right:
#include...
I'm trying build a file in Keil, and have received this error below. Please advise on how to fix it! Thanks!:
*** Using Compiler 'V5.06 update 3 (build 300)', folder: ...
Hello,
I'm trying to put a BLENano board to slepp every loop iteration. These are te steps:
setup:
sd_power_mode_set(NRF_POWER_MODE_LOWPWR);
NRF_POWER->TASKS_LOWPWR...
Can someone tell me the best way to build the old bootloader under SDK 12.
Looking in the examples, in SDK12, there is now only the bootloader_secure example
SDK 11...
Hello
I want to know if we can wake up nrf52832 in sleep mode , from a command through an application on a phone via BLE. If its possible can someone please guide me to...
I want to add backtrace functioanlity in nrf52. I am using functions given in below link:
link text
But I am not getting library files for defining functions mentioned...
Hi,
I have programmed a BLE code.
In the code we are continuously connecting and disconnecting BLE connection.
The BLE connection is established for around say 1 sec...
hi,
This function is called on BLE Event when someone writes to RACP characteristic
What i woud like to know is, is it called from any ISR routine?
Or when BLE Event...
