Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
NRF52 DK on SDK 12.2 (using armGCC)
I have the FDS example from GITHUB working - it shows it is writing and reading the example data (0xDEADBEEF and 0xBAADF00D) fine.
...
EDITTED-
I have a project coming up that uses:
BLE Softdevice, a fair amount of GATT data
SPIM with a fairly high data rate, slave has a RDYN (data ready now)...
Makefile.windows Capture.PNG hello i am trying to make nordic project in eclipse.
for that iam following this tutorial.
https://devzone.nordicsemi.com/tutorials/7/
i...
Hello,
I am using a RFDigital Simblee module (nRF51822 chip) and an ADC with thermocouples to measure high temperatures and process the temperature data via BLE. So I'm...
I created an App with one 16 bit service and some manufacturer data, but the maximum length of manufacturer data that doesn't cause an error is 16 bytes, when in theory it...
Hello,
I have followed the instructions for openwrt on rpi2 devzone.nordicsemi.com/.../
and was able to establish connection Bluetooth 6lowpan connection between Rpi and...
HI I am working with nRF52 DK
softdevice s132 sdk v11.1
I tried out the SPI master and slave examples and they work fine (I can transfer and receive data)
I have been...
Hi,
i have an custom board, using s110 and HID example from sdk9.
After i pair and unpaired few times i get an error code :err_code = 0x8010
err_code = dm_service_context_set...
Hey! I was trying to modify s132 ble_beacon example to s140 for my nRF52840 DK but I couldn't build it in Segger Embeded Studio. What is the problem with "SEGGER_RTT_CONFIG...
Hi,
I have an nrf52 with sd 132 3.0.0 and SDK 12.2 which after turning it on I can connect to it without problems, but after some time (maybe 10-15 minutes) I can't connect...
Hi,
I am using sample ble_hrs code in SDK12.0.0 over Rigado eval Kit for BMD300. After running original code as it is device doesn't advertise. After I commented out the...
I have modified the ble_app_uart to start and stop advertise by receiving command from the uart port. If I don't delete the ble_advertising_on_ble_evt(p_ble_evt); in below...
