I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Dear Nordic Team,
We are using nRF52832 with a IQS231A for proximity detection for a new product, the pins are connected to SDA and SCL and everything is routed as in...
I am now using nrf52832 sdk14.2 development, as a slave device, I want to set the slave's Bluetooth interval is 1S, I set the following parameters: #define MIN_CONN_INTERVAL...
Hello,
I have nRF52832 with custom board and using SDK15 with Keil uVISION 5. I am working on beacon example and I have modified it to show battery level. I have done necessary...
I am using the bootloader_secure_serial example from the SDK 14.0.0 on a 523832 DK. I have erased the device and flashed the softdevice and bootlader on it. The LED1 is turned...
Hey, I would love some guidance on this:
1. I have one NRF52840 advertising constantly at 8dbm, this device is connected to power so it's hard coded to the maximum transfer...
Greetings,
Based on your librairies/examples, I can succesfully write and read data from an external flash (MX25R6435F) using QSPI with DMA.
I'm using a custom board with...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
Hello,
I'm using IAR 8.22.1, SDK 15.0.0, S132, nRF Connect V4.19.2.
I've loaded the 'secure_bootloader' example to PCA10040 EVB.
The device is recognized as DFUTARG...
Need to pass data from a battery powered sensor to a PC via a RF link. Would prefer
a COM Port emulation at 115,200 Baud. I already have a pair of nRF52 Development
Kits...
Hi guys,
Going through mesh packet format today and I'm stumbling upon the time_required_to_send_us method in broadcast.c which is used to calculate and indicate how long...
Hi,
I read and tried Mesh DFU given in " DFU quick start guide of nRF5 SDK for Mesh v2.0.1".
It says "To perform DFU transfers over mesh, use a customized version of...
Hi team,
Is there a way to figure out the phone id (to identify the source of pairing) after the phone has paired with the nordic device?
Basically what we need is is...
Hello,
I've downloaded nRF mesh and installed it on my iPhone, I can use it to provision my device, but there is a question about how to import AppKey on it.
I clicked...
