Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I am using the nRF52 Preview board, PCA 10036. I need to provide a high-frequency clock signal to a peripheral. Anything between 1 and 4 MHz will work. However, I don't need...
I currently call nrfjprog twice to flash the softdevice hex and then the app hex separately. But as I am using two nrfjprog calls, I am unable to set --rbp ALL with the second...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi there,
Currently, I am working on a project which uses iphone(or other IOS device) as a central, and nrf51822 as peripheral.
Basically, the concept is that peripheral...
itg3200.rar hello there i have interfaced itg3200 with nrf51 dk. but now i want to see it on oscilloscope. can you help me?? i have put my scope's screen shot and code here...
HI all,
We've recently moved to SDK 11.0 and it certainly has not been a painless migration, especially when using GCC.
Setup: GCC 5.2.1 on Linux Mint with nrf51 xxAA...
Hi, I'm wonder it is possible to stream video using nRF52x family? I know that chipset isn't designed to this purpose, but I'm only wonder about that.
Thanks
Robert
Hi,
I've started using the nRF5 11.0.0 (89a8197) SDK on a board that does not include an external low-frequency CLK source.
When using the nRF52 0.9.2 SDK, we were recommended...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
