Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi there,
I'm working on a BLE project using the nRF52832 and am having trouble implementing flash storage. I'm using SDK 132 v6.1.1, and the flash storage library to save...
I am implementing the Device Information Service, and want to include the bootloader version as "Firmware revision" in DIS and the application version as "Software revision...
I am new to nordic ble chips.
I am using nrf52832 ble chip, s132_nrf52_3.0.0_softdevice
I am trying to update firmware on the air. But I am getting an error that I do not...
Hey,
Up until now I have only been dealing with software. Now however, I want to create a device that I can use to track my bike by GPS and heading. In the future, I want...
Hi
I am having a problem now(maybe a bug).I refer to nest_state.c and access.c build my user_flash.
But some time,when I reset device,write data to flah will be fail....
Hi,
I'm using the nrf52840 with sdk v15.3 and I'm trying to list of the characteristics of a specific service that has a 128 bit uuid running on a peripheral. However, even...
Hello,
I would like to be clear on the pros/cons of registering a new SIG-adopted UUID versus a vendor-specific UUID. We are a small developer and the cost of registering...
Hello,
I have two differents sensors on one SPI port and I don't really know how to be able to use both. Of course all are connected in the same MISO/MOSI/SCK but there...
Hello,
We currently have several devices out in the field as test units, installed at beta sites. The new modem firmware v1.1 has several features/fixes that we want to...
Hi, we are working on custom board using nRF52811 SOC, I have some confusion
1. regarding the antenna design, I copied the Antenna from Dev board, but it is designed for...
Hello,
There's an interest on the LTE-MTC module.
I can see it's based on nRF9160.
I'd like to inquire about the MTC technology please, does this module support CATM2...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
i want to use pwm of rnf52810.but i don't know how to recognize what pins is pwm.
what pins in 52810 i can use wire to connect and then use it's pwm function?
or i can...
Hello, I try to import big project from Keil to SES. The main idea is to move to better IDE and use the same compiler ARMCC provided by Keil (license is present).
I have...
I am trying to using ceedling with FFF to create mocks of some of the NRFX HAL files. However, when I run ceedling I get some very weird errors. I've taken the `test/include...
