Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
I have understood that sys_evt_dispatch is used for all events that aren't BLE but concern the softdevice.
I start to develop my code on gls_example, here in...
I have an application where I need to synchronize several devices to within 1us using a radio. In order to do this, we need to make a protocol that allows precise synchronization...
We have these Dev Kit Nrf52 and also Nrf51 Bluetooth Smart Beacon Kit. For our application and for the simplest user experience we would like to benefit from update via OTA...
My product only offer a debug interface（SWDIO/REST，SWDCLK，+3.3v，GND），but I learn that the nRF51 DK debug out interface has several pins，such as EXT VTG，EXT GND DETECT，EXT...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
Hi ,
I am using nrf5 SDK v12.2.0 ,
I have an nrf51822 board .. can I just compile the examples in SDK for pca10031 and use it for nrf51822 . Please let me know what I...
Is it possible to have two nRF52 devices connected in such a way to send UART data in a bi-directional way.
Would device 1 be a BLE central and the other BLE peripheral...
I followed the link: infocenter.nordicsemi.com/index.jsp to build and load the app into two boards.
Step 1 ~ 8 are working as expected. But
Step 9 "Observe that LED...
Dear Nordic,
What I want to do:
Battery powered sensor network
One gateway (BLE --> WLAN) with a serial-to-wifi chip connected to nRF52
MQTT (IBM Bluemix -...
