HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
I have a Redbear BLENDv2 and want to program it with Keil. I am new to both Nordik SDK and Keil. Any help how to get to the example or open the example projects
Hello,
My question is about the case when initiator device attempting to restart encryprion with previously bonded responding device that lost the bond context.
As usual...
Hello,
I am trying to interface bme 280 with nrf52. I am using sdk12.2.2 and referring code twi_sensor.
I am able to initialize the I2C drivers and I can read the chip...
Hi,
My name is Bruno, and I am working with a Bluetooth module from u-blox(NINA B112-00B) which contains a nordicSemi board nRF52832 with a Cortex M4 processor. I'm getting...
Hello,
I am trying to combine Softdevice, bootloader, and Application hex files in single hex file.
Currently using s130, SDK11, nrf51822.
I combined files using this...
1, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\peripheral\uart, uarte_irq_handler can get irq when receive a byte.
2, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\proprietary_rf...
Hi,
I made an experiment and the result doesn't correspond with my view on how the BLE communication "connection" mechanism works.
I have an app running on the nRF52832...
Hello All
I am using following SDK version 12.2.0.i am facing some problem in some example project
could you please help me
If i flash the pre compiled hex file...
I held the boot button to enter bootloader mode, and accidentally dropped a hex file into the drive that popped up. Now I can no longer get a comm port to show up on the PC...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
(nRF51822, but also concerned with nRF52832, SD130, SDK 12.1)
I'm trying to write/erase flash from a bluetooth event handler. As it's been outlined in other questions,...
Hi,
I am just updating my application from SDK13.0.0 to SDK14.0.0.
2 Services are in use: DIS and NUS. To advertise that, I made use of the scan response functionality...
Hi,
I have the D52QD2M4IA-A chip (from dynastream) that has inside nrf52832 chip. It has also builtin an onboard LIS2DH accelerometer. However when I am trying to connect...
Hi,
I am working on nrf52832. I am preparing application where I need to handle central connection with two peripherals and keep tracking time. I know that softdevice has...
The data sheet recommends that both the TWI clock and data lines use pull ups and the GPIOs should be set to S0D1, essentially open collector drive. I can see the need for...
