Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Hello forum ,
Here i tried to write and read from flash qspi w25q64 but read and write both are failed ..i m using nrf52840 kindly pls help me for read and write
Hello everyone! I'm currently working on a custom PCB designed specifically for drone communication . In my design, I'm using the nRF52820 as the main microcontroller and...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello Nordic Team,
I am sorry to say this, our development team found a major glitch in micro-esb communication protocol. we are in stage of pre-production of medical sensors...
Hi
We are thinking of using NRF51 for BLE and CPU capabilities. But we also need a Wifi add-on to connect to cloud.
What is the right chipset for this? Which ones are...
I have a demo(s110) set up with some custom services, and in them custom characteristics. The services each relate to a specific sensor element on my device, so have a mostly...
I'm using ble_nus_string_send() to send 15 bytes over BLE UART.
As expected it sends 15 bytes, however on occasion 14 bytes are sent instead of 15 bytes.
Would there...
I ordered nrf8002 IC. I am using following breakout board PCB & not using Nordic development kit.
www.proto-advantage.com/.../product_info.php
I gave 3.3V to both VDD...
I've been working through the tutorials on BLE Services & Characteristics. That's all gone fine for me. Now I'm adjusting the sample code to use different UUIDs for my own...
Dear Sir.
I have a question for app timer in nRF52 DK(pca10040).
I was called a example source(ble_app_hts) for nRF5_SDK_11.0.0-2.alpha.
And I add UART part for logview...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
I am experiencing an error that I can't figure it out why it is happening and where to go and try to fix it.
I am using the subscriber implementation on my nRF51, Raspberry...
I see in multiple examples of NRF51 SDK:
#define APP_TIMER_MAX_TIMERS (2+BSP_APP_TIMERS_NUMBER) /**< Maximum number of timers used by the application. */
but it is...
In ble_gatts.h, I see:
#define BLE_GATTS_FIX_ATTR_LEN_MAX (510) //< Maximum length for fixed length Attribute Values.
#define BLE_GATTS_VAR_ATTR_LEN_MAX (512) //< Maximum...
