I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
hi all,
i have a electronic device having a button which sends continous data till i keep button pressed.
i want to send these data without losing connection.
i can across...
Hello,
I program the nrf51 in C++ using GCC and Eclipse as IDE (this question is not related to the C++ toolchain).
I was wondering if it is possible to add the extern...
Hello!
I bought NFR52 DK preview board. As microcontroller it works well. But when I try BLE examples, they do not work. I installed SoftDevice S132, downloaded ble_app_uart_s132_pca10036...
Hello!
I want to add the battery services in my nRF51822 project for getting the message of battery. Is there need battery-powered?
But,I am sorry to see that the led which...
hi everybody,
I'm working in a project, I need to establish a connection between a beacon & the mobile phone, I want to prevent any other masters of connection to my beacon...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi new to Bluetooth, but familiar with Radios and embedded devices
I have 2 devices that only connect to each other.
in the interest of extreme battery conservation I...
I am using a BLE UART friend module and I am trying to set the GAPIntervals parameters. I realised that when I set my max conn interval parameter above 2000ms, the device...
I am planning to use the nRF51822 and the s130 soft device to manage data coming back bluetooth sensor nodes. It is likely that there will be more than 8 peripherals, although...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...
Hello,
My system is one device with multiple host, these host will connected to the device on irregular basis.
The host action are listed below:
scan->connect->write data...
