Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
I have been forced to upgrade to the nRF54L15 from the nRF52840 DK. The example code in the SDK for the nRF52840 the 'ble-peripheral' had example code for 'ble_app_uart' which...
Hello Nordic,
I’m using ncs\v3.1.0\nrf\samples\peripheral\radio_test` to test the nRF54L15 with PHY set to `NRF_RADIO_MODE_BLE_LR125KBIT`. However, the RF spectrum measurement...
Hello,
I am developing a custom board based on the nRF54L15.
Every time I do RTT connection from the extension i have been asked to prompt the target device (nRF54L15M33...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
The spec. gives a 22V max for a limited amount of time. And max. 5.5V as recommended operating conditions.
But I wonder, what will be "inbetween", e.g. 7V for hours?
From...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hi,
My main() program is
maiin()
{
int rc;
//rc = mcumgr_smp_client_erase(); //printk("mcumgr_smp_client_erase rc=%d\n", rc); //rc = mcumgr_smp_client_confirm_image...
The nPM1304 datasheet shows:
tshipToActive Duration SHPHLD pin must be held low to exit Ship or Hibernate mode: 96 (default)
May we know if debounce is applied to the...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
