I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I recently purchased an nRF51822-mKIT and I'm having great difficulties in getting it to talk to either a Windows 7 or a Windows 8 desktop PC, or a Ubuntu linux desktop PC...
Hi,
I'm having some trouble getting any kind of reaction out of Zigbee logging configurations. I have RTT logging enabled and LOG_DBG("Network left (leave type: %d)", leave_params...
Are there any up to date samples for running BLE on nRF9160 development kit? I've tried building the following sample: https://github.com/nRFCloud/lte-gateway/tree/main for...
Hewy there:
I have a custom nRF52833 board with NCS v3.1.0, using ESB and USB CDC ACM. The external 32 MHz crystal is oscillating fine — we see a clean 32 MHz sine wave...
Hello!
I am having problems reading the SIPINFO on the SoC. I started with the TFM sample and added some lines to read the silicon version. added lines:
printk ...
Hi Nordic Team,
I have been working on the Bluetooth Channel Sounding (CS) Initiator and Reflector samples using nRF Connect SDK v3.3.0 on nRF54LM20B devices , and I was...
When implementing a custom service, the order is usually Generic Access, Generic Attribute, and then the custom service.
Is it possible to change this order to custom services...
I want to develop for the nRF5340 on the Thingy91X. Are there any good sample projects that allow me to set the target board to Thingy91X/nRF5340/cpuapp?
I only need to...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
Hi All,
We have trying the usbd_cdc_acm example program.
It has custom VID and PID. When connected to a windows PC with the correct driver, it is recognised correctly...
Does SDK 3.3 support building hci-lpuart for the Thingy91x yet? I would love to change to that device if it does.
If it does not, are there plans to implement it?
Hi,
I'm running into what looks like a software link-layer issue on the nRF54L15-DK that I'd like a second pair of eyes on. The same firmware works end-to-end with iOS...
Hi,
I’m using GD25WB256 as external flash on nRF9151 for MCUboot secondary slot. It’s currently not available from our supplier, so I’m looking for alternatives.
Current...
