Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
Hi,
I have some problem when scan advertising packet using nrf52840dk with ncs v2.5.0.
when I scan during 30s in the same position, I got a list rssi value same that...
Hi Team,
Hello Team,
I'm currently working on integrating the Sensirion STS40-CD1B-R3 temperature sensor into the peripheral_ht . To do this, I pulled the STS40 driver...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
Hi there!
We are currently evaluating a low-power BLE system for a safety-critical wearable application that must transmit immediate alerts to a nearby receiver or mobile...
I followed the instructions at https://nordicsemiconductor.github.io/pc-nrfconnect-docs/create_new_app to create a new pc-nrfconnect-boilerplate app locally.
However, npm...
We have a common codebase with both softdevice (nRF51/52 code) and now zephyr (nRF54 code). To make our code compatible I have the following replacement to sd_temp_get. This...
Hello Nordic team,
We're experiencing a GNSS issue with our nRF9160-DK (PCA10090 1.1.3 2024.44) and would appreciate any guidance you can provide. About 4 days ago, we were...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
ncs v2.6.1
If I use bt_conn_le_create() and do not use the default (0) value for create_param->timeout, the actual connection creation timeout does not match the description...
