What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
Hi,
I'm using a custom code I developed to save all console logs to an SD card based on the Zephyr architecture. I originally developed it for the Thingy:52 and have also...
Under the old `nrfjprog`, it was possible to check whether the modem firmware matched a particular release by running `nrfjprog --verify mfw.zip` (see )
This is no longer...
Hi everyone,
I’m starting a new project using the nRF54L15 MCU . I’ve worked with the nRF52840 and nRF52832 before, but this is my first time with the nRF54 series.
Due...
Hi,
I am using NRF52833 with soft device version s140. I have set the advertisement duration for the BLE app to 0 (meaning the duration is infinite). Also, I have set scanning...
Hello Nordic Support Team,
I am working on a project using the nRF52832 microcontroller with NRF5 SDK version 13. I have implemented the Flash Data Storage (FDS) module...
Hi Support Team
It seems that there is no current consumption information for SPI and UART of nRF54L15 in data sheet. We want to know the current consumption when SPI and...
I've made an Excel sheet to estimate the power consumption for my nRF51822 device.
Modify light-green fields, to fit your design and see what the estimated current is.
Please...
Hi,
1. I tried flashing all ble codes to my nrf kit. It does not seem to connect on Windows machine but connects on Mac. My other nrf kit connects perfectly fine. What is...
Hi,
I was wondering what I need to do, or if it is even possible, to debug a non-secure app which uses TFM.
Running 'west debug' on e.g. the blinky sample works regardless...
I’m running a self-built BLE application on the nRF52DK board. It used to work fine before, but recently it has stopped working. The board still runs all the sample codes...
Problem : I am following on Bluetooth Fundamental Course on Nordic Academy webpage. I successfully advertising BLE with non-connectable option. But change adv_param to BT_LE_ADV_OPT_CONN...
