If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Board: nRF54LM20A DK
NCS: v3.3.1
I was trying to work with the EGU00 peripheral on the nRF54LM20A, and I realized that it is not present in the device tree definition...
I am using nRF52840 as host processor. Now I need to connect to nRF7002 for WiFi usage. I am using ncs 2.2.2 SDK. I have a few questions? 1. Does nRF7002 work on v2.2.2? I...
I'm running into issues with programming external boards (an NRF52832_xxAA_REV2, an NRF52810_xxAA_REV2, an NRF51xxx_xxAC_REV3, and an NRF52832_xxAA_REV3) through a custom...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Dear nordic This ticket is a feature request to implement SSL max_fragment_length of 2k while initiating a TLS connection, when offloading TLS to the NRF9160 modem. As stated...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
We have two nRF52832-QFAA E0 version devices; Bluetooth works on one, but on the other, it used to work but stopped working over time. Even though we upload the same code...
Hi,
i am working on a project using the nRF54L15.
Hardware: custom board with nRF54L15
Software:
Wirepas SDK (1.6.2)
nrfx drivers (version 3.9.0) with some customization...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello.
I am currently migrating a project from NCS v3.2.4 to v3.3.1 and transitioning from Partition Manager to devicetree-based partitioning, following the official migration...
Hi,
I am using bare metal SDK v2.0.0 and am trying to build the fuel gauge sample inside nrf-bm\v2.0.0\nrf\samples\pmic\native\npm13xx_fuel_gauge. I am using bm_nrf54l15dk...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
