I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi everyone, I am attempting to configure two of NRF5340DK modules to execute ISO_Connected_Benchmark. I have tried to configure ipc_radio to compile for cpunet and application...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I would have a question regarding the use of PCAL6408A I/O expander on nRF9151 DK. The buttons and LEDs on nRF9151 DK are connected both directly to the processor...
We are planning to run a small proto build, and looking to program a small quantity of nRF54L10, prior to the SMT. These are loose parts (not built onto any PCBA). I am hoping...
I recently switched from evaluating an nRF52805 (Fanstel BC805M) to an nRF54L15 (using the nRF54L15-DK), and after I updated the toolchain and tried to flash the kit (using...
checking in if anyone is successfully using an open debug-probe for nRF54L series?
...guessing nordic is using segger OB on the DK's because of the Risc-V not fitting...
Hi,
I'm evaluating the nrf5340-DK board. I have a question about LED5 state. I tried following power sources:
usb J2, sw9 in VDD position - LED5 lights and I can detect...
Hi,
In the example ras_initiator for channel sounding, there is a macro set for maximum TxPower:
where #define BT_HCI_OP_LE_CS_MAX_MAX_TX_POWER 20
In the...
After looking over numerous other devzone tickets and google hits... I cannot get host name to IP address resolution to function on the nRF9151DK. The original source code...
Hello,
I am working with a board (currently embedded inside a clear container I cannot easily take it out of) with an nRF52832-CIAA-R. We were taking photos of it with a...
Dear support team and community
After some days where it worked perfectly, our nRF52840 suddently stopped connecting anymore to a Motorola G4 plus running Android 7.1.1...
Hi, We have tested beacon sample in our custom board. Build with nrf7002dk_nrf5340_cpuapp_ns board config. Facing below issue but the same build is working fine in nrf7002...
Hi all,
I have an issue regarding multiple GPIO interrupts. Following case:
I am using MCP251xfd can module connected via SPI and an interrupt GPIP int-gpios = <&gpio0...
Hello,
Looking for some input on this LTE-M connectivity issue we are seeing.
Hardware: nRF9151, custom board, same result seen on nRF9151DK.
nRF SDK Version: NCS...
