I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Using nRF Connection SDK v3.0.2 and nRF Connection SDK Toolchain v3.0.2
Create a new blank application, "Add build Configuration" for nrf54l15dk/nrf54l15/cpuapp/ns then...
Steps Taken:
Followed the official Nordic guide for adding DFU support to Thingy:91.
Built the project successfully using west build .
Tried flashing via...
Hi all,
Full debug builds ( -Og ) of lwm2m_client simply don’t fit into the nRF91xx targets (nRF9151 DK, Thingy91, Thingy91x). As a workaround I found that building with...
Hi There,
I'm following the "nRF Connect SDK Fundamentals" to set the environment up. The device I'm using is nRF52 kit with N52832 MCU and PCA10040.
The USB wire is works...
Hello,
I am following the official Nordic Academy nRF Connect SDK Intermediate course , specifically Lesson 9 – Bootloaders and DFU/FOTA, Exercise 5 (FOTA over Bluetooth...
Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi, I am no longer able to download the nRF5 SDK version 16.0.0_98a08e2 using curl . A few weeks ago it worked fine, but now I can only download the .zip file through a browser...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
“Why, after setting up the custom board and writing CONFIG_BOARD="my_custom_board" in prj.conf, do I encounter the errors: message(FATAL_ERROR "command failed with return...
I was hoping to access content from DevZone and DevAcedemy content from NotebookLM to combine with my private documentation so I could ask questions specific to my device...
I have been developing software, embedded systems, and hardware for over 30 years, and I must admit: working with nRF Connect + VSCode on Windows (both native and via WSL...
Hello,
I'm experiencing FAT FS corruption (files disappear or files disappear + "volume is full" error on any file write), when I'm unplugging my USB cable. Here is my environment...
Hi everyone! I've recently run into some issues with Bluetooth development, and I'd really appreciate your kind help.
1. Hardware & SDK - SoC: nRF54L15 - SDK: nRF Connect...
Hi, In have the nRF54L15 in System ON IDLE. I can see that enabling WDT31, set up so that it is paused in sleep mode (CONFIG register = 0x4) causes a current increase of ...
Context : SDK2.9, nrf9151
Here is the crypto configuration we had
Our product use MBEDTLS1.2, this is why CONFIG_MBEDTLS_USE_PSA_CRYPTO is set to False.
We are able...
