I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi all,
I am having problems setting up a proper project running the application core and the flpr for nrf54l15. I want to build the FLPR binaries as completely separated...
Hi everyone,
I have a problem with flashing code to Nora-B126, when i press flash in Visual Studio Code everything works fine. I got:
Parsing image file. Verifying programming...
Currently, I am working on nRF5340 Audio DK boards. I am using two nRF5340 Audio DK boards to function as a walkie-talkie using the onboard microphones. Using the nRF5340...
I'm sing NCS SDK 3.3.0:
https://github.com/nrfconnect/sdk-nrf/releases/tag/v3.3.0
Currently I'm using Zephyr sdk 0.17.14. I would like to start using 1.0.1 https://github...
Hello,
in our new project we need to drive a GPIO high as soon as possible after startup.
I have tried with the PRE_KERNEL_1 priority for the device driver but still takes...
Hello everyone,
I am trying to use a nrf52840 dk as an external bluetooth module on my Linux PC to be able to communicate via LE Coded Phy. I have the problem that the devices...
I have a nRF5340 module with an application built using SDK 3.2.1.
The nRF5340 is acting as a CIS Peripheral.
It has an ACL connection and a CIS connection with a Pixel...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
