I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
what is the recommended way on the nRF91x1 to clear the Forbidden PLMN list?
Devices may get denied on networks repeatedly, filling up the FPLMN list. To ensure the...
Hi, we are still struggling with nrf9161 behavior and trying to mitigate data sending dropouts ( and ).
Here is one partial issue: we are currently using UDP and flushing...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
I am currently developing my project using the nrf52832 and the nrf5SDK.
I utilized the peer_manager module, and in the application, when being connected as a peripheral...
The High-Performance Framework (HPF) is a framework designed to support the development and integration of software peripherals using coprocessors (e.g. FLPR on RF54L15)....
Hi,
I managed to get Channel Sounding with Pixel 10 as Initiator working, based on this change on mainline.
https://github.com/nrfconnect/sdk-nrf/commit/30f67fc0b6be8051b5d8f73d900675dd98758631#diff...
Hello Nordic team,
I'm developing a BLE peripheral using nRF52833 and would like to validate that my approach for handling connection parameters aligns with Nordic's best...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan extended adv and print the BASE information in the subgroup in PA, without sink BIS, besides, a smartphone...
Hi,
I am following the course "nRF Connect SDK Fundamentals" and am almost at a standstill when it comes to progress.
I am still struggling with lesson 1 and lesson 2...
Freshly installed VS Code natively on Windows (also tried on Linux and WSL with same result) with NRF Connect Extension Pack, SDK 3.1.1, Toolchain 3.1.1 was used to create...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
