Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
The spec. gives a 22V max for a limited amount of time. And max. 5.5V as recommended operating conditions.
But I wonder, what will be "inbetween", e.g. 7V for hours?
From...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hi,
My main() program is
maiin()
{
int rc;
//rc = mcumgr_smp_client_erase(); //printk("mcumgr_smp_client_erase rc=%d\n", rc); //rc = mcumgr_smp_client_confirm_image...
The nPM1304 datasheet shows:
tshipToActive Duration SHPHLD pin must be held low to exit Ship or Hibernate mode: 96 (default)
May we know if debounce is applied to the...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hello.
I am experiencing an issue where Mesh communication fails after connecting to the SMP Service in the Bluetooth Mesh DFU Distributor sample.
Environment:
NCS...
Summary
On NCS v3.3.0 with CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and a single Ethernet AIL interface (W5500), the Border Router never initialises:
ot br state → uninitialized...
Hello,
We are currently evaluating the nPM1300 as a key component on one of our new designs. This design must support both USB and solar charging using relatively low power...
I recently bought a NRF52840 DK board to teach myself embedded development. I am now following the nRF5 SDK tutorial here:
https://infocenter.nordicsemi.com/index.jsp?topic...
Good morning/afternoon all, I have been working on a BLE air quality monitor using the NRF52810. The first version functioned as expected with the exception of the external...
