I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
Hi Team, We are facing significant range issues on iPhones and other iOS devices with our hardware. We have tested these with both Custom App ( Made in House ) as well as...
Hi Nordic team,
I’m working on an nRF9151 DK with nRF Connect SDK v3.0.0. My goal is to send GNSS latitude/longitude data to a CoAP server.
The GNSS sample works fine...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
1) I'd...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
Hi,
I recently followed the instructions to install nRF Connect on Visual Studio by completing Exercise 1 of the nRF Connect SDK Fundamentals course: Exercise 1-1
I noticed...
I am trying to set CONFIG_TFM_BL2 and it seems like it cannot be set to 'y' because CONFIG_TFM_BL2_NOT_SUPPORTED is also set to 'y' in ${prj_name}/build/${prj_name}/zephyr...
I am using the nRF7002-DK to implement a BLE interface. I need to send packets > 23 bytes through a notification characteristic. I am currently using nRF Connect on an android...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Can you please provide me the peer manager api that can list the paired/bonded devices? Also, is...
Hi,
I would like to ask a few things about Channel Sounding (CS):
Is there any recommendation which method (IFFT, PBR, RTT) should be used for reading the results...
Hi
I`m working with an nRF52833.
I've observed that when the module enters DFU mode, the Bluetooth advertising name seems to be limited to around 22 characters.
If I...
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
