Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
[Environ] nRF Connect SDK v3.2.3 nRF9151 (Custom board) VSCode (1.115.0) Board target: board/nrf9151/ns
When using the PTI firmware, the AT command resulted in an error...
I have a PCB with nRF52833 and nPM1304, I assembled 3 identical PCBs, 2 of them work 1 does not I am using 2 available Buck coveters, first outputs 1.8V for powering IC on...
Hi,
I a\m looking for your recommendation on screen to use with nRFLM20DK board to experiment with LVGL display. Assuming that latest version of nRF Connect SDK has everything...
Hi,
I am using nRF5340 (CPUAPP) with MCUboot and Partition Manager (pm_static.yml, CONFIG_PARTITION_MANAGER_ENABLED=y ).
Build and flash are successful, but during debug...
Dear Technical Support Team,
I have recently been developing with the nRF54L15-DK development board, using the official channel_sounding/cs_test example provided by Nordic...
I am designing a battery system with can charge or supply power via a USB-C PD controller. It will operate up to 20V. I want the option to connect this USB-C D+/D- to the...
Hello, I was able to flash the firmware built using the samples provided by the "nrf connect sdk" using VScode. But, I see failure when I tried to program the nRF54L15 with...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
I was trying to flash a program on nRF52833 development kit and got this error, it important to notice that my college was trying to flash (via VS code) it before and I am...
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I used binwalk to analyze the zephyr.signed.encrypted.bin file generated by the routine mcuboot_with_encryption. I found that the firmware was not encrypted but merely compressed...
We have a peripheral device that maintains a PAwR sync (as a syncer/responder), connects to another peripheral in a central role, and also accepts connections from a central...
