Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...
Hello!
I am sorry to ask a simple question that why my device can't program the ".hex" file about the demo of ble_app_hrs_rscs_relay_s130_pca10028 after I have already program...
Hi,
I have Wifi MCU connected to nr51822.
I download the binary file from a Cloud and need to transfer it via UART, so i need a C code of the nRF5x Programing tool....
Hi,
I am not able to make software breakpoints working with a Segger J-Link probe.
As an exemple, here is my assert callback function:
void __attribute__((noreturn...
Hi.
I'm using nRF51822QFAC, SDK10.0.0, S130.
I want to use DTM code to get SIG certification.
In your example, there is no source code for S130 but S110, S120, S310....
My BLE application needs to occasionally (1-2 times a year) send large amounts (several kbytes) of data, and I'm wondering about how to make this happen as fast as possible...
I am just wondering if anyone else has seen this issue.
I am working on the ble_app_uart_s132_pca10040 on the nRF52 DK.
Using the Android UART v 2.0 app I can connect...
Hi:
A peculiar problem:
I configured an Arduino (atmega328P) to be a receiver and an atmega8A to be a Transmitter Things are fine. The Arduino receives a 10 byte string...
We are developing a beacon device with 10dBm power amplifier. During software development we noticed the control signals provided by ble_common_opt_pa_lna_t align poorly with...
Hi,
As title ,
I try to add the NUS service that show on the ble_app_uart project into Multi-link project.
But it doesn't work .
I want to a central connected to at...
I want to use PWM on only one output pin. I'm using a nrf51422 and softdevice s130.
I want to be able to set the PWM and then change it again (a sequence). This is to be...
I have tried using the pre-built nRFUart Example in the Master Emulator API (2.1.11.1) and get the above error
I also tried rebuilding - no change.
I do have a PCA10000...
Hi everyone,
I'm seeing a weird issue with one of my two instances of 2ch PWMs where if I receive data from TWI, my PWM1 stops functioning and TWI stops functioning as...
A characteristic can be read/write/notify.
I have seen cases in Nordic's examples where there is an internal boolean "is_notify", and when the user sets it from the central...
