hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I am using a nrf51822 based tag and Android official SDK to implement my custom app. I perform the following steps:
1. Scan
2. Connect
3. Discover services
4. Write...
What CRC type is used for the crc calculation with the function
uint16_t crc16_compute (const uint8_t * p_data, uint32_t size, const uint16_t * p_crc )
of the nRf52 SDK...
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...
Hello!
I am sorry to ask a simple question that why my device can't program the ".hex" file about the demo of ble_app_hrs_rscs_relay_s130_pca10028 after I have already program...
Hi,
I have Wifi MCU connected to nr51822.
I download the binary file from a Cloud and need to transfer it via UART, so i need a C code of the nRF5x Programing tool....
Hi,
I am not able to make software breakpoints working with a Segger J-Link probe.
As an exemple, here is my assert callback function:
void __attribute__((noreturn...
Hi.
I'm using nRF51822QFAC, SDK10.0.0, S130.
I want to use DTM code to get SIG certification.
In your example, there is no source code for S130 but S110, S120, S310....
My BLE application needs to occasionally (1-2 times a year) send large amounts (several kbytes) of data, and I'm wondering about how to make this happen as fast as possible...
I am just wondering if anyone else has seen this issue.
I am working on the ble_app_uart_s132_pca10040 on the nRF52 DK.
Using the Android UART v 2.0 app I can connect...
Hi:
A peculiar problem:
I configured an Arduino (atmega328P) to be a receiver and an atmega8A to be a Transmitter Things are fine. The Arduino receives a 10 byte string...
We are developing a beacon device with 10dBm power amplifier. During software development we noticed the control signals provided by ble_common_opt_pa_lna_t align poorly with...
Hi,
As title ,
I try to add the NUS service that show on the ble_app_uart project into Multi-link project.
But it doesn't work .
I want to a central connected to at...
I want to use PWM on only one output pin. I'm using a nrf51422 and softdevice s130.
I want to be able to set the PWM and then change it again (a sequence). This is to be...
I have tried using the pre-built nRFUart Example in the Master Emulator API (2.1.11.1) and get the above error
I also tried rebuilding - no change.
I do have a PCA10000...
