Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I use the SDK12.3 and SD130 with secure_bootloader and my own application. I can flash SD and Bootloader and update my app over OTA with DFU from NRF Toolbox. My app...
I noticed that when upgrading to the latest Thread SDK that my devboard stopped booting. I was following the instructions as per the documentation but noticed that my user...
Hi,
I am designing a custom PCB using the nRF51422. I want to include an external 16 MHz crystal oscillator to use as X1 according to the reference layout for custom PCBs...
When I test the timer example with nrf52832 DK, it so nice to 4 minutes.
uint32_t time_ms = 240000;
But when I set the time interval over 5 minutes, then the event...
What is the maximum number of bond table entries a device can have?
If a device allows only one connection to be established at once (not more than one simultaneously)...
Hi,
I want to store the CRC of the current firmware in the flash, for DFU purposes. Almost all of the threads I've seen so far reference the pstorage API but it's no longer...
I am searching for a basic example to understand the build system.
How do I load the soft device properly?
How do I set things up to run SEGGER_RTT_WriteString?
I...
I am using Nrf52832 sdk 11.I want to update the value of characteristic on every read operation from my andriod phone. I want that on every ble_gatts_evt_read: should give...
Hi! Im trying to figure out the power consumption of two types of beacons that uses nRF51 and nRF52. I have connected a small resistor in between the supply and measuring...
Preferrably under linux using gcc and the command prompt.
I am most interested in project setup, loading the soft device, and making sure all the core systems are working...
I am running the ble_app_uart example in SDK 13.0 with nRF52382.
First issue
The app can receive data via UART only when I use "Termite" as a terminal emulator...
Hi, trying to implement timeslot api and stuck with TIMER0.
I saw similar questions but answers is still unclear.
My timer init code:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi
I am using nrf52832 with softdevice s132_nrf52_3.0.0.
In my appliocation I need to do periodic measuremets, and it is critical that softdevice doesn't interrupt during...
Hi,
I have to make a interrupt each 100us. This interrupt should be priority on the BLE. In my interrupt I have only one condition (if/else) and I have to change PWM value...
Hello,
I'm looking to implement the OTA on my nRF52, but I couldn't find any help online.
I would like to do it with my iOS and my Android app.
Does anyone have a tutorial...
