Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
(PLEASE SEE COMMENT BELOW)
I've got a Nordic project that I imported into Eclipse as a makefile project. I've got it working and I can debug into it. Everything is good....
OTA problem：
My hardware is 51822qfaa .
This my bootloader: nRF51_SDK_10.0.0_dc26b5e.rar
location: nRF51_SDK_10.0.0_dc26b5e\examples\dfu\bootloader\pca10028\dual_bank_ble_s110...
how many uart can I use at the same time in nrf52832
i know in nrf51822, every pin can use as uart,but at the same time ,i can only use one uart.and now ,i have a case...
Hi,
I have an issue with app_timer (nRF52, SDK13.0).
I use a single shot timer.
I try to debug, and I'm in the case of app_timer.c line 650:
ticks latest: 534879...
We need to connect at the same time
several mobile phones with the Android OS to a single device
nrf51822 via BT in our upcoming project.
According to information from...
Hey,
Just had a quick question... I was doing the Relay example and I don't totally understand what a "relay" is. Can you explain what the purpose and usage of relay is for...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
