Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
Hi,
I am working on custom Board with nrf52382, I am using the mma8652 accelerometer for different functionality(prior is single and double tap detection).
Initially...
Hi,
Because of the compatibility issues I'm trying to use SDK10 for my nRF51422 device,
the problem is that I have flashed the S130 softdevice and the ble_app_uart, and...
I want to use FDS in my application. Lets assume I do not have a bootloader. This is part of my linker script describing memory regions.
MEMORY
{
FLASH (rx) : ORIGIN...
I am using proximity profile for my custom board as a tracker.I would like to make the services read/write operations accessable only to my andriod app.Others can connect...
Hello,
Recently I purchased a BLE Nano Kit with MK20/ DAP Link USB Board - Bluetooth 4.0 Low Energy Module Development Board from Fab2Lab and I was trying to use the nRF...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
Dear all,
I have a project with a nRF51822 based on S110 and SDK10.
Almost everything is running fine, but every time I scan for devices, either by calling BluetoothAdapter...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
