Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi Sir,
I'm studying the nRF52840-PDK, and i found there are two debug connector. One is Debug in connector (P18) and another is Trace connector (P25).
As check the...
Hi!
I am fully aware on how Eddystone works. Or at least I believe so. Sadly there is some weirdnesses when I am trying to broadcast using the Nordic SDK.
So what am...
Hello , ebery one
Please let me have a question about PCA 10040.
When you connect a USB cable, it acts as a virtual drive and if you copy hex format (such as Hart rate...
I'm trying to determine DFU_APP_DATA_RESERVED and FDS_VIRTUAL_PAGES.
According to this Q&A, DFU_APP_DATA_RESERVED must be the same FDS_VIRTUAL_PAGES, if FDS_VIRTUAL_PAGE_SIZE...
Hello,
I am using pca10040 and sdk 12.2.2. I want that my pca10040 should advertise for 10 sec then it should go to system off mode then it should wake up after 20 sec. My...
Hi everyone,
I was wondering if the nRF52840 DK will have NCP OpenThread support for wpantund Linux (other than Raspberry Pi) or if it already exists. I flashed the nRF52840...
Hello ,
I want to establish a connection between the adxl345 nrf51822.
Nrf51822 is working both individually and Adxl345. I would be glad if I can provide you with necessrat...
We are building a new version of a small device with the new nRF52832. Its only external connection is a micro USB plug that we use for charging - we do not need it as USB...
Hi,
I'm evaluating a nRF52 as ble central - controlled from a windows pc.
Searching the forum I just found:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/....
Hi,
I am trying to connect 4 devices with the pc-ble-driver. Therefore I modified the heartrate example.
3 Devices are connecting fine - on the 4th connection request...
