Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
Hi Nordic, can you please confirm the device ID for nRF51822 QFAA G1?
The HWID I discovered is 0x004A
Pls confirm so I can pull an update request for Black Magic Probe...
I tried to run the ble_app_hrs_freertos example on the pca10040 devkit, but it's not possible to connect via ble (using nrf connect, neither with pc nor with smartphone)....
Hello,
I'm testing the capability of BT5 so I bought two nRF52840 Preview DK (I also have one nRF52832 DK) and I have some questions that may speed up the work.
...
Hello,
i am writing an application which uses the SDK13 peer manager library for bonding. The Nordic chip is acting as a peripheral.
Is there an easy way to prevent...
Hi，I update my IAR IDE from version 7.70.1 to 8.11.1，when I compile the workspace ble_app_hrs_freertos_pca10040, the error occur in port.c, as following:
Error[Og014]:...
First try to create a TWIM driver from scratch without any DMA. Following the steps in the OPS I get mixed behavior and only the chapter with DMA generates any clock and data...
I ran into an odd issue on nRF52840 using s140 version 5.0.0-3.alpha. My application erases and writes to a region of flash.
I've found that I'm able to erase the pages...
Hello,
I have implemented experimental DFU buttonless example with my application and able to do the firmware OTA via secure bootloader example using private and public...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
Hello,
I am trying to implement DFU secure bootloader to do firmware update over the air for nrf51822.
I have followed the steps as per the blog
devzone.nordicsemi...
Hello,
I want to ask, did the nordic chip support I2C slave ? I want to make other controller (STM) as Master and Nordic chip as slave in I2C.
Is it possible? or Nordic...
Hello!
I am trying to increase the MTU size to get higher speeds. When I increase the MTU above 65 the application locks/software reset when doing transfer. Up to 65 it...
