Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
Hello,
I am trying to implement DFU secure bootloader to do firmware update over the air for nrf51822.
I have followed the steps as per the blog
devzone.nordicsemi...
Hello,
I want to ask, did the nordic chip support I2C slave ? I want to make other controller (STM) as Master and Nordic chip as slave in I2C.
Is it possible? or Nordic...
Hello!
I am trying to increase the MTU size to get higher speeds. When I increase the MTU above 65 the application locks/software reset when doing transfer. Up to 65 it...
Hi, I'm facing an extremely strange problem with a product I'm developing.
I've been getting significant idle current measurements (around 7 mA), and I couldn't for the...
I recently attempted to upload a new image via OTA.
After emailing the zip file to my iPhone as an attachment and tapping on it,
then tapping on the share icon several choices...
Hello,
I need a voltage regulator to power a microphone at 1.3V from a 3V coin cell battery and I was looking for a regulator like the lm317 , but with this one the minimum...
IAR EW 8.11.1 does not link the nfc samples from sdk 13.1. There are different sizes for wchar_t:
Error[Lt009]: Inconsistent wchar_t size
nfc_t2t_lib.o(nfc_t2t_lib_iar...
Q1 I compile sdk13.0.0 generate nrf52840_xxaa.hex(app), nrf52840_xxaa_s140.hex(bootloader).
I used merge tool make a hex file, then burn the file into PCA10056 DK by nrfjprog...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the softdevice to work as s130 for its (simultaneous Central/Peripheral...
HI,
the solution I'm working on requires quite a few IO pins, so once I ran out of regular GPIO pins I had to resort to using NFC ones.
I changed the UICR registers...
I am using the Dynastream D52DK1 ANT starter kit -based on Nordic Semiconductor’s nRF52832. According to the documentation given by Dynastream,
Open the desired project...
