Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
So I switched from Bluemod+S (nRF51822) to Bluemod+S42 (nRF52832) on my custom board and am trying to adapt my existing code to work on the newer model. Apart from various...
Hello,
can anybody tell me the exact differences between a Link Layer Acknowledgement and the Acknowledgement used by a write Request?
Does anybody have some statistics...
I am trying to implement the Current Time Service in my project and had a few questions:
-The example requires that security be established before services can be discovered...
hai
i am using mbed to program my nrf51822. in my application i need to read two analog sensor values.
i am using p5 and p6 pin for that.
AnalogIn analog_pin_1(p5);...
Can somebody explain what 0xA1 means in this raw L2CAP layer:
0a, 00, 4d, 00, A1, 01, 00, 00, 08, 00, 00, 00, 00, 00
I know 0a, total bytes, and 4d is channel ID, I...
Hello
I was wondering whether is possible to use an updated version of the softDevice into an older SDK, my current hw is a nRF52832pca10040 DK
For example, I am currently...
Hi,
I am using experimental_ble_app_blinky example. In that NRF_LOG over UART was implemented.
I Added some UART code for my use. But after flashing code was not working...
I am using SDK14 and SD132 V5 on nrf52382. I tested the hids_mouse example and it autoconnected without any issues to the phone. In my application, I have 2 modes. Config...
Hi,
We're designing a product with the nRF52 (SoftDevice S132 v5.0.0 production) and an external WiFi module, and are attempting to do a "poor man's WiFi Co-Existence"...
I am struggling to figure out the correct IRAM/IROM settings in keil for the ble_app_beacon example in sdk 14.0.
I am currently using this example on an nrf52 DK and will...
Hi!
I just bought a BLE Nano board featuring nRF52832 chip.
I am using it with Arduino IDE, controlling some servos and motors onboard my autonomous device.
I would like...
I am trying to set up a project for the nRF51 by hand and by looking at the example code provided by Nordic.
I am using Softdevice 130 on a nRF51422 and the 12.0.1 SDK...
Hi,
I'm using SDK12.3.0, 52DK with the "experimental_ble_app_hids_keyboard_pairing_nfc" project, I follow this post and using the setting:
IROM1: Start: 0x1F000 Size: 0x61000...
